Description
Everything above the load is a promise. A four-leg chain sling is the part of a lift that nobody photographs and everybody stands under. The Four Point is built to the only specification that matters in that position: G80 manganese alloy steel chain, forged alloy hooks with self-locking catches, and an 11,000 lb working load with a four-to-one safety factor behind it.
The geometry is what makes four legs worth having. A single-leg sling lifts a load at one point and lets it swing; four legs distribute the load across a wider footprint and hold a machine frame, a crate or an engine block level through the lift. Each leg is 5/16 inch or 8 mm chain with a 5 ton assembly rating, and the assembly is rated as a system rather than as four separate chains, which is the number a rigger actually needs. Working lengths run from 1.5 m through 3 m to 4 m so the same sling serves a low trailer deck and a high crane hook.
The hooks are forged alloy steel with self-locking safety catches that close automatically as the load seats, which prevents the slip that causes most lifting incidents. The chain is powder coated for wear and corrosion resistance, and manganese steel holds its original length under load rather than stretching into a permanent set. Before every lift the rule is the same: inspect the links, confirm the hook catches close, and never exceed the rated capacity. Rated capacity is per assembly in the stated configuration, and a leg pulled at an angle reduces it.
A sling that never gets noticed is a sling doing its job.
Key Features
- ✦ 5 tonne / 11,000 lb assembly working load with a 4:1 safety factor
- ✦ G80 manganese alloy steel chain, 5/16 inch / 8 mm, four legs
- ✦ Forged alloy steel self-locking hooks that close automatically under load
- ✦ Breaking strength above 800 MPa with resistance to permanent stretch
- ✦ Available in 1.5 m, 3 m and 4 m working lengths
- ✦ Powder-coated chain for wear and corrosion resistance
- ✦ Rated as a complete four-leg assembly, not as individual chain lengths
Technical Specifications
- MaterialG80 manganese alloy steel
- Chain diameter5/16 in / 8 mm
- Legs4
- Working load limit11,000 lb / 5 t
- Safety factor4:1
- Breaking strengthOver 800 MPa
- Working lengths1.5 m / 3 m / 4 m (5 ft / 10 ft / 13 ft)
- HooksForged alloy, self-locking safety catch
- FinishPowder coated
- CertificationCE
- ApplicationCrane, hoist, forklift and shop lifting
Where It Belongs
Machine shops moving engine blocks and castings between stations; warehouses lifting crates and palletized loads where a level pick matters; auto workshops pulling engines with an overhead hoist; and yards repositioning heavy equipment that a two-leg sling would tilt. The four-leg arrangement is the correct choice whenever the load has four usable attachment points and must stay horizontal through the lift.
Questions Buyers Ask
What does the 5 tonne rating actually refer to?
It is the working load limit of the complete four-leg assembly in a vertical configuration. Loads pulled at an angle reduce the capacity, as with any sling.
How much does the rating drop when legs are at an angle?
Significantly. At a 45 degree leg angle the effective capacity falls by roughly 30 percent. Riggers should calculate the angle rather than assume the vertical rating.
What is the safety factor?
Four to one. The assembly is proof tested well beyond the working load limit and rated down to a quarter of that figure.
Are the hooks self-locking?
Yes. The forged alloy hooks have safety catches that close automatically as the load seats, which prevents the load from slipping out if tension slackens.
Which length should I choose?
Measure from the crane hook to the load attachment points. 1.5 m suits a low deck and short hook height, 3 m is the general workshop standard, and 4 m suits high hook positions and tall loads.
Can the legs be shortened?
The assembly is supplied at a fixed working length. Shortening it requires certified re-termination; do not modify chain slings in-house.
How often should it be inspected?
Before every lift, visually. A formal inspection is recommended at least every six months in regular use, looking for bent links, worn bearing points, cracked hooks or a catch that does not close.
Does it work on a forklift?
It can be suspended from a certified forklift lifting point. Never hang it from the forks themselves without a rated attachment.
Is powder coating hiding chain damage?
The coating is thin and does not conceal link deformation. Any link that looks bent or worn through the coating should be flagged and the sling removed from service.
Can I get a certificate of test?
Yes. Request the test certificate with your order and we include the load test documentation for compliance files.
The EastSupplier Promise
Every unit is inspected before it leaves the warehouse and ships from the region closest to you. If a specification on this page does not match what arrives, we replace it. Requests are answered within one business day by people who handle the product, not a script. EastSupplier supplies brands, workshops and retailers across North America, Europe and Australia from a catalog of more than fifty thousand lines.






Customer Reviews
Payment and Security
Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.
