Description
A failed print is rarely a design problem. It is a spool problem. A bubble two hundred grams into a roll, a diameter that drifts four hundredths of a millimeter, a batch that warped because the polymer absorbed a week of humid air before it was sealed. The Spool Archive is a ten-roll set of PLA Plus at 1.75 mm with a plus or minus 0.02 mm tolerance and a zero-bubble claim, which is the specification that decides whether a print finishes or fails at eighty percent.
PLA Plus is not plain PLA with a marketing prefix. The impact strength reaches 8 kJ/m2, roughly two to three times standard PLA, which is what stops a part from shattering when it is dropped rather than flexing. That matters for brackets, enclosures, jigs and anything that leaves the printer and enters a workshop. The 330 meter length per kilogram spool means ten rolls is more than three kilometers of material before you reorder, and the neat wind without knots means a print that runs overnight does not stop at layer four hundred with a tangle.
The printing window is documented rather than guessed. Between 205 and 215 degrees C the material runs clean at 50 to 100 mm/s; from 215 to 245 degrees it holds at 100 to 200 mm/s for faster work. Bed temperature is 50 to 60 degrees, which is reachable on an unheated glass bed with glue stick or a PEI sheet. Low shrinkage keeps long parts flat, so a 200 mm bracket prints without lifting at the corners. RoHS and REACH documentation covers the material for shops that need compliance paperwork, and the 1.1 kg net weight is honest: you get a full spool, not a short one.
Material is the only variable in a print you cannot fix afterward.
Key Features
- ✦ Ten spools of 1.75 mm PLA Plus, 1.1 kg net per roll, roughly 330 m each
- ✦ Plus or minus 0.02 mm diameter tolerance for consistent extrusion
- ✦ Zero-bubble extrusion that eliminates mid-print voids
- ✦ Impact strength up to 8 kJ/m2, two to three times standard PLA
- ✦ Documented temperature windows: 205-215 C at 50-100 mm/s, 215-245 C at 100-200 mm/s
- ✦ Low shrinkage so long parts stay flat without corner lift
- ✦ Neat knot-free winding that survives overnight prints
- ✦ RoHS and REACH documentation available for commercial shops
Technical Specifications
- BrandJAYO
- MaterialPLA Plus
- Diameter1.75 mm
- Tolerance+/- 0.02 mm
- Net weight1.1 kg per roll
- Gross weight1.35 kg per roll
- LengthApprox. 330 m per roll
- Print temperature205-215 C at 50-100 mm/s; 215-245 C at 100-200 mm/s
- Bed temperature50-60 C
- Impact strengthUp to 8 kJ/m2
- CertificationRoHS, REACH
- Shelf life1 year sealed
Where It Belongs
Design studios running multiple printers through a week of prototypes; workshops printing jigs, brackets and fixtures that need to survive handling rather than sit on a shelf; schools and maker spaces that want a single material predictable enough for students to succeed with; and small production runs where a color change mid-project would mean a visible seam. Ten rolls also solves the most common operational problem in a print farm, which is running out at hour nine of an eleven-hour job.
Questions Buyers Ask
How many rolls are in the set?
Ten spools, each 1.1 kg net weight and approximately 330 meters of 1.75 mm filament.
Is PLA Plus stronger than standard PLA?
Yes. Impact strength reaches up to 8 kJ/m2, roughly two to three times standard PLA, which mainly shows up as resistance to shattering on impact.
What temperature should I print at?
205 to 215 C for detail work at 50 to 100 mm/s, and 215 to 245 C for faster printing at 100 to 200 mm/s. Bed at 50 to 60 C.
Does it work on a printer without a heated bed?
It will print on blue tape or glue stick on an unheated bed for small parts. A heated bed at 55 C is strongly recommended for anything with a large footprint.
What does zero bubble actually mean?
The filament is degassed during manufacture so there are no voids inside the strand. Voids cause under-extrusion and weak spots that show up as a print failing partway through.
Will the spools fit a standard printer?
The spools are standard 1 kg format with a 1.75 mm strand and fit typical AMS and side-spool holders. Check your holder's maximum spool diameter if it is 200 mm or smaller.
Is the diameter tolerance consistent across all ten rolls?
The specification is plus or minus 0.02 mm per roll. In practice that is tight enough that you do not need to re-tune flow between rolls in a set.
Does it need drying before use?
It arrives vacuum sealed and is ready to print. Once a spool has been open for several weeks in humid air, drying at 45 C for four hours restores it.
Can it be used for functional parts?
For indoor functional parts, yes. For sustained load, heat exposure above 55 C, or outdoor UV, PETG or ASA is the better material.
Is there compliance documentation for commercial use?
RoHS and REACH documentation is available. Request it at the time of order and we include it with the shipment.
The EastSupplier Promise
Every unit is inspected before it leaves the warehouse and ships from the region closest to you. If a specification on this page does not match what arrives, we replace it. Requests are answered within one business day by people who handle the product, not a script. EastSupplier supplies brands, workshops and retailers across North America, Europe and Australia from a catalog of more than fifty thousand lines.








Customer Reviews
Payment and Security
Vos informations de paiement sont gérées de manière sécurisée. Nous ne stockons ni ne pouvons récupérer votre numéro de carte bancaire.
