Descrizione
Every aluminum frame starts as a pile of straight lines. What turns those lines into a machine, a bench, a gantry or a safety enclosure is the corner, and the corner is where cheap builds fail first. A squared end butted against another squared end holds nothing but friction and hope. The bracket is the part that decides whether the frame stays a rectangle under load or slowly becomes a parallelogram.
This is a vertical rectangular corner in 6063-T5 aluminum, anodized after machining. The alloy is the one extrusion profiles themselves are made from, which is why thermal expansion across the joint stays matched and why a frame assembled in a cold workshop does not loosen in a warm one. The gusset form carries the load as a web between two faces instead of through the bolt holes alone, so the bolt clamps the joint and the web resists the racking force. That is the whole mechanical argument for a bracket over a butt joint.
The range covers the profiles people actually build with: 2020, 3030, 4040, 4545, 6060, 8080, 9090 and 100100. Each size is machined for its own slot geometry rather than being a scaled drawing, because a bracket that fits a 20 series slot cleanly will not seat on a 40 series profile without play. The anodized finish is a working surface, not a cosmetic one: it resists the light abrasion of a workshop, keeps the joint from galling when it is dismantled and reassembled, and stays electrically insulating where the frame carries sensors and wiring.
The one thing worth reading twice is what the price covers. It is an individual corner piece. Nuts and screws are not in the box, because builders on this scale already buy fasteners by the hundred and resent paying for two bolts per bracket. Buy the T-nuts and the cap-head screws that match your profile, decide early whether the frame is a permanent weldment or a fixture you will reconfigure, and the corner stops being a line item and becomes the reason the frame is still square in five years.
Straight lines are easy. A corner is where a builder tells the truth.
Key Features
- 6063-T5 aluminum The same alloy as the extrusion it clamps, so the joint moves with the frame instead of fighting it.
- Anodized after machining A hard, electrically insulating surface that resists galling when the joint is broken down and rebuilt.
- Vertical rectangular gusset A machined web across both faces resists racking, which is the failure mode a butt joint cannot survive.
- Eight profile sizes 2020, 3030, 4040, 4545, 6060, 8080, 9090 and 100100, each cut for its own slot geometry.
- Load spread across two faces The bolt clamps; the web carries. Force leaves the joint through the bracket instead of through the fastener.
- Sold as single pieces Buy one for a repair or a hundred for a production run, without a minimum order sitting behind it.
- Fasteners excluded by design Nuts and screws are not bundled, because builders at this scale already buy them in bulk.
- Rebuildable Loosen, realign, retighten. Nothing in the joint is welded, pressed or single-use.
Technical Specifications
- Material: 6063-T5 aluminum
- Finish: Anodized, clear
- Form: Vertical rectangular corner with internal gusset web
- Profile sizes: 2020, 3030, 4040, 4545, 6060, 8080, 9090, 100100
- Fixing method: T-nuts and cap-head screws into the profile slot
- Fasteners included: No. Nuts and screws sold separately
- Unit price covers: One corner piece, without nuts or screws
- Slot bolt guidance: M5 on 20 series, M6 on 30 and 40 series, M8 on the larger profiles
- Surface conductivity: Electrically insulating when anodized
- Tolerance: Machined to the nominal profile, squared to the joint face
- Working environment: Indoor workshop, machine frame, enclosure, lab fixture
- Reuse: Fully demountable without damage to bracket or profile
Where It Belongs
This is the part for the person building the frame rather than buying it: the CNC enclosure, the 3D printer gantry, the test rig, the workbench, the camera rail, the extraction hood, the light truss over a bench. It suits automation cells that get reconfigured every few months because the joint comes apart cleanly. It also suits the one-off repair where a single corner on a purchased frame has cracked and the whole assembly is too expensive to replace.
Frequently Asked Questions
Q: Are nuts and screws included?
A: No. The price covers the corner piece only, which is stated on the listing and is deliberate. You need T-nuts and cap-head screws matched to your profile slot; most builders already hold both.
Q: Which bolt size do I need?
A: Follow the slot. The 20 series takes M5, the 30 and 40 series take M6, and the 45 series and above take M8. If the profile came from a different supplier, check the slot width rather than assuming the series number settles it.
Q: Will it fit my extrusion if I did not buy the profile here?
A: Almost certainly, if the profile is a standard T-slot. These brackets are machined to the common slot geometry across the 20, 30, 40, 45, 60, 80, 90 and 100 series, which is shared by most suppliers.
Q: How many brackets does a frame need?
A: One per corner, so four for a single rectangle and eight for a box. Long spans and cantilevers usually want an extra pair at the mid-span joint, and any frame carrying a motor wants all eight.
Q: Is 6063-T5 strong enough for a machine frame?
A: For static and light dynamic loads, yes. It is the alloy the extrusion is made from, so the frame behaves as one material rather than two. For high-vibration or safety-critical structures, add diagonal bracing instead of leaning on a thicker corner.
Q: Can I reuse them?
A: Yes. Nothing in the joint is welded or pressed, so the bracket comes off with the same two bolts that put it on. That is the reason to keep the fasteners in a labelled bin.
Q: Does the anodized finish scratch?
A: It resists workshop abrasion well, but it is a surface, not armour. A scratched bracket is still structurally sound and still electrically insulating at the joint face.
The EastSupplier Promise
Every unit ships from inspected stock held by our own team, not from a blind dropship queue. Orders placed before 3pm warehouse time leave the same working day, and each parcel carries a tracking number you can follow from dispatch to doorstep. If a unit arrives damaged or does not match this listing, we replace or refund it inside 30 days.
- Stock checked daily: the inventory figure on this page is live, not a placeholder.
- Technical answers in English: a human replies to product questions within one business day.
- No surprise fees: the price you see is the price at checkout.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.