Descrizione
A print fails at the spool long before it fails at the nozzle. Moisture, a tangled wind, a diameter that drifts three hundredths of a millimetre off spec — none of these announce themselves, and all of them surface twelve hours into a job as stringing, layer chatter or a nozzle that plugs mid-bridge. The Layer Forge exists to remove those variables. Two kilograms of Geeetech PETG, vacuum sealed at the factory, wound tight, and delivered in colours that hold their saturation after cooling.
PETG occupies the practical middle ground between the ease of PLA and the durability of ABS. It is tougher and far less brittle than PLA, tolerates mild outdoor exposure, resists many common solvents, and — critically for anyone who prints parts that must actually function — it does not shatter on impact. Shrinkage is low, dimensional stability is high, and the material bonds between layers with real mechanical strength rather than the surface adhesion that gives PLA its brittle reputation. It is also odour-light and non-toxic in normal use, which matters when the printer sits in a room where people work.
The spool geometry is where most budget filament quietly fails. At 1.75 mm with a tolerance of plus or minus 0.03 mm across 343 metres of material, the extruder sees a consistent bite, which is why the flow stays even at both 50 and 100 mm per second. Air bubbles are eliminated at the vacuum seal, so the melt is uniform and the surface finish comes out glass-smooth instead of bubbled. It runs on essentially any FDM machine, from a stock bedslinger to a modern enclosed printer, and it is specified for crafts, artwork and industrial design samples alike.
Material is not a consumable. It is the first decision in every print that follows.
Why This Spool Behaves
- ✦ Vacuum sealed in 2 kg total — moisture is the number one cause of PETG stringing, and it never gets in.
- ✦ Diameter tolerance of plus or minus 0.03 mm — consistent extruder bite across the whole spool.
- ✦ Low shrinkage, high dimensional stability — large flat parts stay flat.
- ✦ Tough rather than brittle — functional parts bend instead of shattering.
- ✦ Bubble and tangle free wind — no mid-print snags, no surface voids.
- ✦ 343 metres of usable material — long jobs without a splice.
- ✦ FDM universal — runs on enclosed printers, bedslingers and everything between.
Filament Data
- Material: PETG (polyethylene terephthalate glycol)
- Diameter: 1.75 mm
- Tolerance: plus or minus 0.03 mm
- Total Net Weight: 2 kg
- Length: approx. 343 m
- Extrusion Temperature: 220 to 240 C (428 to 464 F)
- Bed Temperature: 80 to 90 C (176 to 194 F)
- Print Speed: 50 to 100 mm/s
- Shelf Life: 2 years when sealed
- Packaging: Vacuum sealed, rigid spool
What People Actually Print With It
PETG earns its keep wherever a print has to survive contact with the world. Mechanical brackets and jigs that would crack in PLA. Enclosures for electronics that sit in a garage where the temperature swings. Replacement knobs, clips and latches for equipment whose spare parts no longer exist. Vases and lampshades where translucency and a smooth wall finish are the whole point. Design studios use it for form studies that need to look like production parts rather than prototypes. Two kilograms is also the practical quantity for a working week: enough to finish a serious assembly without stopping mid-job, and sealed tightly enough that the second spool is still dry when you open it a month later.
Print Questions
Q: Is PETG harder to print than PLA?
A: Slightly. It wants a hotter bed, slower first layer and modest part cooling to avoid stringing. Once dialled in, it is as repeatable as PLA and considerably stronger. A bed temperature of 80 to 90 C and an extrusion range of 220 to 240 C is the working window.
Q: Why does vacuum packaging matter?
A: PETG absorbs moisture from the air, and absorbed moisture turns to steam at the nozzle, causing popping, stringing and weak layer bonds. A factory vacuum seal means the spool you open behaves exactly like the spool that was tested.
Q: How many spools are in the 2 kg option?
A: The listing is sold as a 2 kg total bundle, arranged as 1 kg spools so each spool can be handled and stored normally. Select the colour combination you want at checkout.
Q: Can it be printed on a printer without an enclosure?
A: Yes. PETG does not demand an enclosure the way ABS does. Draft shielding around the machine is enough for large flat parts, which are the only geometry sensitive to uneven cooling.
Q: Does it work with a hardened nozzle and direct drive extruder?
A: It works with both direct drive and Bowden systems, and with brass, hardened steel or ruby nozzles. No abrasive additive is present, so nozzle wear is not a concern with this material.
Q: What happens if a spool sits open for weeks?
A: It will pick up ambient moisture. Two hours in a filament dryer at 65 C restores it. Storing the spool in a sealed box with desiccant is the routine that keeps results consistent.
Q: Is PETG food safe or outdoor safe?
A: It is generally considered suitable for occasional outdoor use because of its UV and chemical resistance, but it is not certified food contact material, and printed layers can harbour residue. Treat it as an engineering material rather than a kitchen one.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.