Descrizione
The Tool That Cuts What Nothing Else Can Reach.
An oscillating multi-tool is the answer to a specific problem: a cut that has to happen in place, in a corner, flush to a surface, with the workpiece already installed. Undercutting a door frame for new flooring, trimming a skirting board around a pipe, slicing a mortise into a fitted jamb, cutting a nail buried in timber without destroying the blade. A circular saw cannot start in the middle of a board, a jigsaw cannot cut flush, and a chisel needs space to work. The multi-tool does it by moving a small blade sideways at high frequency instead of spinning it.
Frequency is what makes that work. This one runs from 10,000 to 20,000 oscillations per minute with a 4 degree swing, and the quick release lever means a blade change takes seconds rather than the two minutes a hex bolt takes when your hands are full. Maximum output is rated at 740 watts with anti-vibration isolation in the body, which is the difference between a tool that stays controllable through a long cut and one that leaves your hand buzzing after thirty seconds of plaster.
The battery platform is the Makita 18 volt system: BL1830, BL1840, BL1840B, BL1850 and BL1850B all fit, with a 2.0 to 5.0 amp hour capacity recommended. It is explicitly not compatible with the DC18WA, BL1813G or BL1413G packs, which is worth knowing before you order a bare tool for a battery you already own. Three configurations are stocked: one battery set, two battery sets, or tool only with no battery and no charger for people already on the platform.
Most tools need room to work. This one needs a millimetre and a decision.
Specification Notes
- 10,000 to 20,000 OPM — Frequency range for timber, plaster, plastic and metal
- 4 Degree Oscillation — Swing angle that cuts without needing a starting hole
- 740W Maximum Output — Rated output for continuous cutting and sanding work
- Quick Release Blade Change — Lever release rather than a hex bolt
- Anti-Vibration Isolation — Keeps the body controllable through long cuts
- Flush and Plunge Cutting — Cuts in place, in corners, against a surface
- Makita 18V Compatible — BL1830, BL1840, BL1840B, BL1850 and BL1850B packs
- Three Configurations — One battery, two batteries, or bare tool
Technical Specifications
- Type — Cordless oscillating multi-tool
- Oscillation Frequency — 10,000 to 20,000 OPM
- Oscillation Angle — 4 degrees
- Maximum Output Power — 740 W
- Blade Change — Quick release lever
- Battery Platform — Makita 18V, BL1830 / BL1840 / BL1840B / BL1850 / BL1850B
- Not Compatible With — DC18WA, BL1813G, BL1413G packs
- Recommended Capacity — 2.0 to 5.0 Ah
- Configurations — 1 battery set, 2 battery set, or bare tool
- Accessory Mount — Standard oscillating tool interface
- Intended Use — Renovation, flooring, joinery, plumbing and automotive trim
- Condition — New
The Jobs It Gets Called For
A flooring installer undercuts door frames and architraves so new boards slide beneath them, which is impossible with any other tool in a fitted room. A plumber cuts a pipe access slot into a fitted cabinet back panel without removing the cabinet. A joiner trims skirting around a radiator bracket that was never going to come off cleanly. An electrician cuts plasterboard for a back box without a dust shower from an angle grinder. An automotive restorer slices seam sealer and trim clips that resist everything else. A renovator uses it with a scraper blade to lift vinyl and adhesive before a floor replacement, which is the least glamorous job it does and the one it saves the most time on.
Questions Worth Asking
Q: Which batteries fit?
A: Makita 18 volt packs: BL1830, BL1840, BL1840B, BL1850 and BL1850B. It does not fit DC18WA, BL1813G or BL1413G. Check the pack you own before ordering the bare tool version.
Q: Do I need to buy blades separately?
A: Blades are consumables and are not the point of the tool listing. Order the blade types the job needs: a bi-metal blade for nails and metal, a wood blade for clean timber cuts, a scraper for adhesive and a sanding pad for finishing.
Q: What does the 4 degree swing mean in practice?
A: The swing angle sets how aggressively the blade bites. Four degrees is the common working angle: enough to cut efficiently without stalling the motor in a tight plunge.
Q: Can it cut through a nail in timber?
A: That is what a bi-metal blade is for. A wood blade will lose teeth on a nail. Expect to go through blades on nail-heavy work, which is normal for the tool rather than a fault.
Q: Is it variable speed?
A: The tool runs across a 10,000 to 20,000 OPM range so speed can be matched to material. Drop the frequency for plastic and laminate, raise it for timber and plaster.
Q: Which configuration should I order?
A: Order the two battery set for site work where charging time matters, one battery set for occasional use, and the bare tool if you already own Makita 18V packs and a charger.
Customer Reviews
Payment and Security
Le tue informazioni di pagamento vengono elaborate in modo sicuro. Non memorizziamo i dettagli della carta di credito né abbiamo accesso alle informazioni della tua carta di credito.