説明
Headphones die in a predictable order. The pads flatten, the cable fails at the jack, the headband cracks, and the drivers, which are the expensive part, usually still work perfectly. Throwing a pair away because a five dollar cable gave up is absurd, yet it happens constantly, because most owners do not know that a replacement driver is available and that fitting one takes a soldering iron and fifteen minutes. This is the part that makes repair the sensible option.
The unit is a 40mm driver with a 64 ohm voice coil, a specification that sits in the sweet spot for portable gear: high enough impedance to keep hiss low from a phone or a small amp, low enough that nothing exotic is needed to drive it. Inside, a 20 core neodymium magnet provides the motor force, and the coil uses imported copper clad aluminum wire, which is the same construction used in drivers costing several times this price. The diaphragm is a three layer composite, and it is the same class of material found in the HD598 and HD650, which is why the midrange stays composed instead of turning brittle at volume.
Measured behaviour matters as much as materials. Frequency response runs from 20Hz to 20kHz with sensitivity around 120dB, so the driver is efficient enough to reach listening level without strain, and the deep bass the listing promises is a function of magnet strength and diaphragm compliance rather than equalisation. Total height is about 9mm, which keeps the assembly shallow enough to fit inside most over ear cups. Buy one to replace a failed channel, or two to rebuild a pair with matched output.
The most sustainable headphone is the one you did not throw away.
What Makes It Different
- ✦ 40mm driver with 64 ohm impedance for phones, dongles and small amplifiers
- ✦ 20 core neodymium magnet motor for controlled low frequency output
- ✦ Imported copper clad aluminum voice coil
- ✦ Three layer composite diaphragm of the class used in HD598 and HD650 designs
- ✦ Sensitivity around 120dB for easy drive without strain
- ✦ 20Hz to 20kHz rated response with a shallow 9mm profile
- ✦ Available as a single unit or a matched pair for a full rebuild
Technical Specifications
- Driver Diameter: 40mm
- Impedance: 64 ohm
- Frequency Response: 20Hz to 20kHz
- Sensitivity: 120dB plus or minus 3dB
- Magnet: 20 core neodymium
- Voice Coil: Imported copper clad aluminum wire
- Diaphragm: Three layer composite
- Total Height: Approximately 9mm
- Connection: Solder terminals
- Package Contents: One or two driver units per option selected
Where It Belongs
Repair shops use it to bring dead headphones back to service without hunting for donor units. DIY owners replace a single failed channel and keep the original housing, cable and pads. Small builders use pairs in custom cups for a first headphone project, and tinkerers drop a set into vintage frames whose drivers have hardened over decades. Because the impedance is 64 ohm, the same unit works in wired gaming headsets, studio monitors and portable players.
Questions Buyers Ask
Q: Can I replace just one driver?
A: Yes, and the single unit option exists for exactly that. Match the impedance and diameter of the surviving driver, and check that both channels sound balanced before closing the cup.
Q: Do I need to solder?
A: Yes. The terminals are solder tabs, so a basic iron and rosin core solder are required. Work quickly at low heat, because the voice coil lead is thin and heat soaking into the coil will damage it.
Q: Will it fit my headphones?
A: It fits any cup with room for a 40mm driver and roughly 9mm of depth behind the grille. Measure the old driver before ordering, and check that the mounting face has space for the solder tabs.
Q: Is 64 ohm too high for a phone?
A: No. Modern phones and USB dongles drive 64 ohm loads comfortably. It is high enough to reduce background hiss compared with 16 ohm designs.
Q: What causes the bass to sound thin after a rebuild?
A: Usually an air leak. The cup must seal around the driver, so check the gasket and the pad seal before judging the driver itself.
Q: Can I use two of these to build headphones from scratch?
A: Yes. Choose the pair option and design the cup volume around a 40mm driver. The 20Hz rating assumes a sealed or well damped enclosure.








Customer Reviews
Payment and Security
お支払い情報は安全に処理されます。 クレジットカードの詳細を保存したり、クレジットカード情報にアクセスすることはありません
