{"product_id":"the-float-line-pneumatic-ball-transfer-units","title":"The Float Line | Pneumatic Ball Transfer Units for Panel Saw Tables","description":"\u003cdiv class=\"product-narrative\"\u003e\n\u003cp style=\"line-height:1.8;margin:0 0 18px 0;\"\u003eA full sheet of eighteen-millimetre laminate weighs more than most people assume. Laid on a steel bench it becomes an argument — you push, it resists, the edge digs in, the cut wanders. Laid on a film of air, the same sheet moves under one finger, and the saw tracks exactly where the operator intended.\u003c\/p\u003e\n\u003cp style=\"line-height:1.8;margin:0 0 18px 0;\"\u003eThese spring-loaded ball transfer units are the small, unglamorous components that make that film of air possible. Each unit seats into a drilled pocket on a pneumatic table, lifting a hardened steel ball a fraction of a millimetre above the surface. Air escapes through the gap, the panel floats, and friction drops from a fight to a whisper. The spring pin beneath each ball lets the assembly give slightly under load, so a heavy panel does not stall the transfer — it is supported by dozens of points distributing the weight instead of a single hard contact.\u003c\/p\u003e\n\u003cp style=\"line-height:1.8;margin:0 0 18px 0;\"\u003eThe range covers eight configurations for a reason. Air bearing tables are built by the people who use them, and every table has its own geometry: pocket depth, panel mass, feed direction. Dark grey SCM15 units suit standard 16 mm pockets; stepped bias types hold alignment in tables that have already been re-machined; the high-quality 18 mm units carry heavier panels without flat-spotting; the 22 mm bias and the two springless 21 mm float variants serve press beams and suction-cup gantries, where the ball must sit flush and return predictably. Matching the unit to the table is the whole job.\u003c\/p\u003e\n\u003cp style=\"font-style:italic;line-height:1.8;margin:26px 0 0 0;\"\u003eA panel does not move because you push harder. It moves because the surface underneath finally agrees to let go.\u003c\/p\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-features\" style=\"margin-top:30px;\"\u003e\n\u003ch3 style=\"font-size:20px;font-weight:600;margin-bottom:14px;\"\u003eKey Features\u003c\/h3\u003e\n\u003cul style=\"list-style:none;padding:0;margin:0;\"\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Spring pin suspension absorbs load changes instead of transferring them to the panel face.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Hardened steel ball rotates in any direction, so panels feed and rotate without lifting.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Eight pocket configurations covering 16 mm, 17 mm, 20 mm and 22 mm bore tables.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Dark grey and polished finishes available to match existing table hardware.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Individual replacement units — rebuild a worn table point by point instead of scrapping it.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Low seat height keeps the working plane unchanged after a retrofit.\u003c\/li\u003e\n\u003cli style=\"margin-bottom:10px;font-size:15px;\"\u003e✦ Drop-in installation in pre-drilled pneumatic tables, no adapter plate required.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-specs\" style=\"margin-top:30px;\"\u003e\n\u003ch3 style=\"font-size:20px;font-weight:600;margin-bottom:14px;\"\u003eTechnical Specifications\u003c\/h3\u003e\n\u003cul style=\"list-style:none;padding:0;margin:0;\"\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eFunction:\u003c\/strong\u003e Pneumatic ball transfer unit for air bearing tables\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eApplication:\u003c\/strong\u003e Panel saws, sliding table saws, suction cup gantries, press feed tables\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eLoad Principle:\u003c\/strong\u003e Spring-supported ball, air film assisted\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eVariants:\u003c\/strong\u003e 8 types — SCM15, bias with and without step, ordinary, high quality, bias 22, two springless floats\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003ePocket Compatibility:\u003c\/strong\u003e 16 mm, 17 mm, 20 mm and 22 mm bores\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eBall Material:\u003c\/strong\u003e Hardened steel\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eHousing Finish:\u003c\/strong\u003e Dark grey or polished\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eSpring:\u003c\/strong\u003e Integral coil spring, or springless on float variants\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eMounting:\u003c\/strong\u003e Press fit or drop-in into machined pocket\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eQuantity:\u003c\/strong\u003e Sold per unit\u003c\/li\u003e\n\u003cli style=\"padding:9px 0;border-bottom:1px solid #eee;font-size:15px;\"\u003e\n\u003cstrong\u003eOrigin:\u003c\/strong\u003e Mainland China\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-applications\" style=\"margin-top:30px;\"\u003e\n\u003ch3 style=\"font-size:20px;font-weight:600;margin-bottom:14px;\"\u003eWhere It Belongs\u003c\/h3\u003e\n\u003cp style=\"line-height:1.8;margin:0;\"\u003eShop-built pneumatic tables, panel saw infeed and outfeed extensions, sliding table retrofits, vacuum suction gantry rails and press feed lines all rely on this class of component. Anyone who has dragged a melamine sheet across a bare steel bench and watched the blade climb knows the difference a properly sprung ball transfer makes. Cabinet shops, millwork houses and machinery rebuilders buy these as consumables — a table with forty points will eventually wear four of them, and replacing four units costs far less than replacing a table.\u003c\/p\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-faq\" style=\"margin-top:30px;\"\u003e\n\u003ch3 style=\"font-size:20px;font-weight:600;margin-bottom:14px;\"\u003eFrequently Asked Questions\u003c\/h3\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: How do I know which of the eight types fits my table?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eMeasure the bore diameter of an existing pocket and note whether it has a machined step. SCM15 fits a 16 mm pocket, the bias types fit 17 mm pockets with or without a step, ordinary and high-quality units fit 20 mm, and the 22 mm bias and 21 mm float variants cover larger press and gantry bores. If you are drilling fresh pockets, choose the unit first and machine the pocket to match.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: Will these work on a table that was not originally pneumatic?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eYes, provided the table has enough structure to drill and seat the pockets. The units are point supports, so a table with a thin sheet top needs local reinforcement beneath each pocket. Once seated, the air supply is a low-pressure feed to the plenum under the table.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: What happens when a ball wears a flat spot?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eThe panel begins to drag in one direction and the saw cut pulls to one side. Because these are sold individually, you replace only the affected points rather than the table. Most shops keep a small stock of the type they use most.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: Are the springless variants a downgrade?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eNo. They serve a different job. Springless float units sit flush and return on air pressure alone, which is what suction-cup gantries and press beams require. Spring units suit tables where the panel rests directly on the balls.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: Can I mix types on one table?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eYou can, and some rebuilders do: heavier units under the load-bearing half, lighter units at the infeed. Keep ball height consistent across the table or the panel will rock as it passes.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003cdiv style=\"margin-bottom:16px;\"\u003e\n\u003cp style=\"font-weight:600;margin:0 0 6px 0;\"\u003eQ: How many units does a typical table need?\u003c\/p\u003e\n\u003cp style=\"margin:0;line-height:1.7;\"\u003eEnough that no single ball carries more than roughly a twentieth of the panel mass, spaced so the panel cannot bridge and sag between points. A three by two metre table commonly uses forty to sixty units.\u003c\/p\u003e\n\u003c\/div\u003e\n\u003c\/div\u003e\u003cdiv class=\"product-gallery\" style=\"margin-top:32px;text-align:center;\"\u003e\n\u003ch3 style=\"font-size:20px;font-weight:600;margin-bottom:18px;\"\u003eProduct Gallery\u003c\/h3\u003e\n\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Hbf5bd901a4a24b67a7b5898a0858c76aI.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/H8c5791ef28944504b497b526d4051bf6d.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Hdd6f3c23d07d4a53adcb6653a2d16c57m.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Hd8fe12a5abb7463cb4871f9d1d0a9e496.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/H9929321a95c4452693d60fa8dc8ee7aet.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Sd014a90a941946199683c1d0888175a9Q.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S7515e02ee0294fec8b90fe42eb8f2f46J.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/S2bc5f5fd184e4749a21f6c52138af555C.webp?v=1773279966\" alt=\"Pneumatic floating ball transfer unit for panel saw table\" loading=\"lazy\" style=\"max-width:100%;height:auto;margin:0 0 14px 0;border-radius:6px;\"\u003e\n\u003c\/div\u003e\u003cscript type=\"application\/ld+json\"\u003e{\"@context\":\"https:\/\/schema.org\",\"@type\":\"Product\",\"name\":\"The Float Line | Pneumatic Ball Transfer Units for Panel Saw Tables\",\"description\":\"Spring-loaded pneumatic ball transfer units for air bearing tables, panel saws and suction gantries. Eight pocket configurations from 16 mm to 22 mm.\",\"sku\":\"FLOATLINE-ABT\",\"brand\":{\"@type\":\"Brand\",\"name\":\"EastSupplier\"},\"url\":\"https:\/\/eastsupplier.com\/products\/the-float-line-pneumatic-ball-transfer-units\",\"image\":\"https:\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Hbf5bd901a4a24b67a7b5898a0858c76aI.webp?v=1773279966\",\"offers\":{\"@type\":\"Offer\",\"priceCurrency\":\"USD\",\"price\":\"22.56\",\"availability\":\"https:\/\/schema.org\/InStock\",\"url\":\"https:\/\/eastsupplier.com\/products\/the-float-line-pneumatic-ball-transfer-units\",\"seller\":{\"@type\":\"Organization\",\"name\":\"EastSupplier\"}},\"aggregateRating\":{\"@type\":\"AggregateRating\",\"ratingValue\":\"4.67\",\"reviewCount\":\"3\",\"bestRating\":\"5\",\"worstRating\":\"1\"}}\u003c\/script\u003e","brand":"East Supplier Platform","offers":[{"title":"Type6","offer_id":48582586925279,"sku":"1005003336704629-Type6","price":187.85,"currency_code":"USD","in_stock":true},{"title":"Type5","offer_id":48582586958047,"sku":"1005003336704629-Type5","price":39.31,"currency_code":"USD","in_stock":true},{"title":"Type8","offer_id":48582586990815,"sku":"1005003336704629-Type8","price":46.27,"currency_code":"USD","in_stock":true},{"title":"Type7","offer_id":48582587023583,"sku":"1005003336704629-Type7","price":46.27,"currency_code":"USD","in_stock":true},{"title":"Type1","offer_id":48582587056351,"sku":"1005003336704629-Type1","price":37.97,"currency_code":"USD","in_stock":true},{"title":"Type2","offer_id":48582587089119,"sku":"1005003336704629-Type2","price":37.97,"currency_code":"USD","in_stock":true},{"title":"Type4","offer_id":48582587121887,"sku":"1005003336704629-Type4","price":27.07,"currency_code":"USD","in_stock":true},{"title":"Type3","offer_id":48582587154655,"sku":"1005003336704629-Type3","price":43.01,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0503\/6412\/1244\/files\/Hbf5bd901a4a24b67a7b5898a0858c76aI.webp?v=1773279966","url":"https:\/\/eastsupplier.co.uk\/ja\/products\/the-float-line-pneumatic-ball-transfer-units","provider":"EastSupplier Platform","version":"1.0","type":"link"}