The Float Line | Pneumatic Ball Transfer Units for Panel Saw Tables

Save 20%
East Supplier PlatformSKU: 1005003336704629-Type6

Color: Type6
Price:
$187.85 $234.81

Tax included Shipping calculated at checkout

Stock:
In stock

Description

A full sheet of eighteen-millimetre laminate weighs more than most people assume. Laid on a steel bench it becomes an argument — you push, it resists, the edge digs in, the cut wanders. Laid on a film of air, the same sheet moves under one finger, and the saw tracks exactly where the operator intended.

These spring-loaded ball transfer units are the small, unglamorous components that make that film of air possible. Each unit seats into a drilled pocket on a pneumatic table, lifting a hardened steel ball a fraction of a millimetre above the surface. Air escapes through the gap, the panel floats, and friction drops from a fight to a whisper. The spring pin beneath each ball lets the assembly give slightly under load, so a heavy panel does not stall the transfer — it is supported by dozens of points distributing the weight instead of a single hard contact.

The range covers eight configurations for a reason. Air bearing tables are built by the people who use them, and every table has its own geometry: pocket depth, panel mass, feed direction. Dark grey SCM15 units suit standard 16 mm pockets; stepped bias types hold alignment in tables that have already been re-machined; the high-quality 18 mm units carry heavier panels without flat-spotting; the 22 mm bias and the two springless 21 mm float variants serve press beams and suction-cup gantries, where the ball must sit flush and return predictably. Matching the unit to the table is the whole job.

A panel does not move because you push harder. It moves because the surface underneath finally agrees to let go.

Key Features

  • ✦ Spring pin suspension absorbs load changes instead of transferring them to the panel face.
  • ✦ Hardened steel ball rotates in any direction, so panels feed and rotate without lifting.
  • ✦ Eight pocket configurations covering 16 mm, 17 mm, 20 mm and 22 mm bore tables.
  • ✦ Dark grey and polished finishes available to match existing table hardware.
  • ✦ Individual replacement units — rebuild a worn table point by point instead of scrapping it.
  • ✦ Low seat height keeps the working plane unchanged after a retrofit.
  • ✦ Drop-in installation in pre-drilled pneumatic tables, no adapter plate required.

Technical Specifications

  • Function: Pneumatic ball transfer unit for air bearing tables
  • Application: Panel saws, sliding table saws, suction cup gantries, press feed tables
  • Load Principle: Spring-supported ball, air film assisted
  • Variants: 8 types — SCM15, bias with and without step, ordinary, high quality, bias 22, two springless floats
  • Pocket Compatibility: 16 mm, 17 mm, 20 mm and 22 mm bores
  • Ball Material: Hardened steel
  • Housing Finish: Dark grey or polished
  • Spring: Integral coil spring, or springless on float variants
  • Mounting: Press fit or drop-in into machined pocket
  • Quantity: Sold per unit
  • Origin: Mainland China

Where It Belongs

Shop-built pneumatic tables, panel saw infeed and outfeed extensions, sliding table retrofits, vacuum suction gantry rails and press feed lines all rely on this class of component. Anyone who has dragged a melamine sheet across a bare steel bench and watched the blade climb knows the difference a properly sprung ball transfer makes. Cabinet shops, millwork houses and machinery rebuilders buy these as consumables — a table with forty points will eventually wear four of them, and replacing four units costs far less than replacing a table.

Frequently Asked Questions

Q: How do I know which of the eight types fits my table?

Measure the bore diameter of an existing pocket and note whether it has a machined step. SCM15 fits a 16 mm pocket, the bias types fit 17 mm pockets with or without a step, ordinary and high-quality units fit 20 mm, and the 22 mm bias and 21 mm float variants cover larger press and gantry bores. If you are drilling fresh pockets, choose the unit first and machine the pocket to match.

Q: Will these work on a table that was not originally pneumatic?

Yes, provided the table has enough structure to drill and seat the pockets. The units are point supports, so a table with a thin sheet top needs local reinforcement beneath each pocket. Once seated, the air supply is a low-pressure feed to the plenum under the table.

Q: What happens when a ball wears a flat spot?

The panel begins to drag in one direction and the saw cut pulls to one side. Because these are sold individually, you replace only the affected points rather than the table. Most shops keep a small stock of the type they use most.

Q: Are the springless variants a downgrade?

No. They serve a different job. Springless float units sit flush and return on air pressure alone, which is what suction-cup gantries and press beams require. Spring units suit tables where the panel rests directly on the balls.

Q: Can I mix types on one table?

You can, and some rebuilders do: heavier units under the load-bearing half, lighter units at the infeed. Keep ball height consistent across the table or the panel will rock as it passes.

Q: How many units does a typical table need?

Enough that no single ball carries more than roughly a twentieth of the panel mass, spaced so the panel cannot bridge and sag between points. A three by two metre table commonly uses forty to sixty units.

Customer Reviews

Customer Reviews

Based on 3 reviews
67%
(2)
33%
(1)
0%
(0)
0%
(0)
0%
(0)
E
Ellis P.
Bought individually and that is the whole point

A table with forty points eventually wears four of them. Being able to buy singles instead of a kit is why I keep coming back. Two units arrived in a padded box, seated in ten minutes, table back in service the same afternoon.

D
Doreen W.
Right part, measure your pockets first

Ordered Type1 for a 16mm bore table and they dropped straight in. Quality of the ball and spring is better than what came out of it. Taking one star off only because I had to measure three times to be sure which of the eight types I needed, so buy the caliper out before you order.

L
Lowell M.
Finally a table that behaves like the saw deserves

We retrofitted an older sliding table with these and the difference on a full sheet of 18mm melamine is dramatic. One hand moves the panel now. The spring give is the part I did not expect - a heavy sheet settles instead of stalling the transfer, so the feed stays smooth right through the cut. Ordered a spare set of four for when the first points wear.

Payment and Security

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently Seen