The Violet Cure | 405nm Photopolymer Resin for LCD and DLP Printers

Save 20%
EastSupplier PlatformSKU: 1005007294147530-green-United States

Color: green
Price:
$39.32 $49.15

Tax included Shipping calculated at checkout

Stock:
In stock

Description

Resin printing is a negotiation between detail and durability, and the resin is where that negotiation is settled. Ask for a finer tip and the material must flow into a smaller cavity; ask for a part that survives being dropped and the cured surface must be hard enough to resist it. Most resins pick one and quietly abandon the other, which is why a workshop ends up with three bottles and a shelf of failed prints to explain them.

This one is formulated for the 405nm wavelength that LCD and DLP machines actually emit, with viscosity in the 300 to 400 MPa.s band so it drains from fine channels instead of pooling in them, and hardness of 80 to 90D after cure. Extension strength sits at 45 to 65 MPa and flexure at 55 to 80 MPa, which is the range where a functional bracket or a housing holds its shape under load without becoming brittle at the screw bosses. Density of 1.05 to 1.15 g/cm closes the loop on exposure calibration: the numbers are consistent, so a profile you dial in on one bottle transfers to the next.

The practical part is that it prints detail the 4K and 8K screens can resolve. A 0.05 mm layer on a modern mono screen is only worth running if the resin can hold the edge, and this one does on miniature work, dental models, jigs and small mechanical parts alike. It comes in one kilogram bottles in green, white and blue, which covers the workshop that needs one bottle rather than a chemistry set.

Detail is cheap. Detail that survives being used is the material's job.


Where It Performs

  • ✦Formulated for 405nm LCD and DLP printers, including 4K and 8K mono screens.
  • ✦Low viscosity that drains fine channels instead of clogging them.
  • ✦Hardness of 80 to 90D after full cure for parts that hold their shape.
  • ✦Extension strength 45 to 65 MPa and flexure 55 to 80 MPa.
  • ✦Consistent density and viscosity for repeatable exposure profiles.
  • ✦One kilogram bottles in green, white and blue.
  • ✦Suitable for miniatures, models, jigs and small functional parts.

Technical Data

  • Form: Liquid photopolymer
  • Wavelength: 405 nm
  • Compatibility: LCD and DLP resin printers, 4K and 8K screens
  • Volume: 1 kg
  • Hardness: 80 to 90D
  • Extension strength: 45 to 65 MPa
  • Flexure strength: 55 to 80 MPa
  • Viscosity: 300 to 400 MPa.s
  • Density: 1.05 to 1.15 g/cm3
  • Shore and finish: Hard surface, suitable for painting after cure
  • Storage: 15 to 25 degrees C, sealed, out of UV light
  • Shelf life: 1 year from production when stored correctly
  • Origin: Mainland China

What It Gets Used For

Miniature painters use it because the edge definition survives a primer coat. Model makers use it for parts that have to fit together after curing, where dimensional consistency matters more than surface gloss. Workshops use it for jigs, brackets and small housings that need to hold a thread. Dental and orthodontic labs use it for study models, where the requirement is a clean surface and a repeatable result from bottle to bottle. The one thing it is not for is a part that must flex under load, which is a different resin family entirely.

Working With It

Q: Which printers does it suit?

Any LCD or DLP resin printer exposing at 405 nm, including 4K and 8K mono screen machines. It is not for SLA laser printers that expose at a different wavelength.

Q: What layer height should I use?

Between 0.03 and 0.05 mm for detail work, and up to 0.1 mm for larger parts where speed matters more than surface. Exposure times vary by machine, so run a calibration print before committing to a long job.

Q: How long should parts be cured?

Wash in isopropyl alcohol first, dry fully, then post-cure under a 405 nm station in short increments, checking between them. Over-curing makes parts brittle, which is the most common cause of a part that snaps later.

Q: Is it brittle?

It is a hard, rigid resin, so thin unsupported features will snap under bending just as they would in a hard plastic. For parts that must flex, use a flexible resin rather than this one.

Q: How should I store it?

Sealed, between 15 and 25 degrees C, away from UV light. Filter resin back into the bottle through a mesh after a failed print, and never leave it in the vat for weeks.

Q: Does it smell strongly?

It has the normal acrylic odor of photopolymer resin. Ventilate the printing room, wear nitrile gloves, and avoid skin contact, which is standard practice for any resin.

Q: What is the shelf life?

One year from production when stored sealed and cool. Resin that has thickened noticeably in the bottle should be filtered and tested before a critical print.

Customer Reviews

Customer Reviews

Based on 3 reviews
67%
(2)
33%
(1)
0%
(0)
0%
(0)
0%
(0)
M
Mireille X.
No strong smell, predictable exposure

Same profile worked from the first bottle onward. White takes primer well and does not yellow after a week under a window, which was my worry.

L
Lorcan G.
Hard and dimensionally consistent

Brackets fit first time across two bottles, which is more than I can say for the last brand I used. It is rigid, so thin features snap if you bend them, which is expected for this hardness.

K
Kezia P.
Detail holds after curing

Ran it at 0.04 mm on a 4K mono screen and the edge definition survived priming. Viscosity drains from fine channels instead of pooling, which cut my failed prints noticeably.

Payment and Security

PayPal

Your payment information is processed securely. We do not store credit card details nor have access to your credit card information.

Estimate shipping

You may also like

Recently Seen